Neptunes aquarium manual#
Neptunes aquarium free#

As just one example, you might be dosing an Alkalinity solution and a misconfiguration could lead to overdosing of your tank.

NOTE: Neptune Systems recommends you re-calibrate the pumps every 100 hours of operation or any time you change to a liquid with a substantially different viscosity.OUT OF RANGE ACTIONS AND ALERTS You can set up your Apex to alert you, or take immediate action(s) when a parameter falls outside of the safe zone you specify. RepeatВ the above steps for the other pump.YourВ reading is from the meniscus and precision is important.Note that the liquid in the cylinder curves upward at the walls of the cylinder.

ItвЂ™s important to view it directly level with the liquid level- donвЂ™t view it at an angle.Please note when reading from theВ graduatedВ cylinder.The pump will run for 90 seconds attempting to dose 40 ml, then stop.ДЄfter it stops, note how much water is in the graduated cylinder after the 90 seconds and enter that value on the Display Screen. OnВ the Display Screen press вЂOKвЂ™ to start CalibratingВ the Pump. Move the вЂOUTвЂ™ cup away and nowВ place the outgoing tubing into your graduated cylinder. WeВ are going to prepare to calibrateВ the pump.

Neptunes aquarium manual#

Now, hold down the manual priming button on the DЕЊS and watch your pump start to transfer water from one cup to to just about the end of the outbound tube.В Keep at itВ till liquid flows freely into your empty cup and there are no air bubbles in the tubing line. The Display Screen will instruct you to prime the pump.

On your Apex Display Screen navigate to:.

Place the вЂINвЂ™ tubing intoВ the cup with water and then place the вЂOUTвЂ™ tubing into the empty cup. Also have your included graduated cylinder handy. Get two cups and fill one of them with water (tap is fine). Visually inspect your tubing and length as well as the compression fitting for each tube. Place the compression fitting on your measured tubing and then connect it to DЕЊSВ pumps. A good method to securingВ the tubing in your aquarium or sump is using the Neptune Systems Magnetic Probe Rack (MPR). Measure the length of tubing that will be needed to connect your DЕЊS pumps from your additive container and aquarium connectors. Now that you have a good idea of where your DЕЊS will be mounted we can measure and cut the tubing to the appropriate length. Remove the compression fitting from your pump cover by turning it counter-clockwise.ДЇour meters of tubing was included with your DЕЊS purchase. Moving forward and in the configuration of the DЕЊS pumps, we will always assume the the tubing coming from your additive container is connected to the вЂњinвЂќ and tubing goingВ to your aquarium will be connected to the вЂњout.вЂќ While the pump can run forward or reverse, typically it will run вЂњinвЂќ to вЂњout.вЂќ So вЂњinвЂќ will be liquid coming from a container and вЂњoutвЂќ will be going to your aquarium. On your DЕЊS pump cover and peristaltic assembly there is an вЂњInвЂќ and and вЂњOutвЂќ label. PLEASE NOTE: Neptune Systems always recommends that all equipment be mounted above the water line and/or with appropriate drip loops! The DOS can pump up to 24вЂІ vertical feet without any loss of head pressure.

Again, in certain equipment failure scenarios, this could possibly cause an unintended gravity siphon. It should be just above your water level. We also recommend that yourВ DЕЊS tubing never be submersed in your tank. Although extremely unlikely, this could cause a gravity siphon in certain equipment failure scenarios. It is of the utmost importance that your fluid reservoirs be placed below yourВ DЕЊS module. The DЕЊS pumps were designed offset so tubing would not kink if multiple DЕЊS modules were stacked on top of each other.

Easy punch out mounting holes on the back so that it can be mounted inside your cabinetry or wall.

Use these for supplementing your DOSвЂ™s schedule with addition amounts. The LED status light will turn blue when the pump is running.

Neptunes aquarium free#

If you choose to plug into your Energy Bar be sure that outlet mode is set to ON.Д¬onnect the 6вЂІ aquabus cable to your DЕЊS module and any available aquabus port on another Neptune SystemsвЂ™ module.ДЄfter the initial connections have been made, the status light on the DЕЊS will glow orange.ДЇor manual rotation control of each motor there are two priming buttons located on the center of DЕЊS.ДЇeel free to test the motors are in operating condition by pressing the priming buttons on Pump 1 (Left) and Pump 2 (Right). It does not need to be plugged into an Energy Bar outlet.

Connect the 24V Power Source to a wall outlet and your DЕЊS module.